Autel Can’t Program The 2nd Key on VW CC Tips & Solution

Want to add a key for remote start, and able to program the first key but can’t program the second key on a VW CC 2015.
I am assuming the key is locked from the dealer and previously worked with the car. If I put this back in the car since I have a key matched, should I be able to program the two keys properly via OBDII?

What he has done to troubleshoot the issue:
1.OBD programming (Expert mode)
Path:
IMMO>>Volkswagen>>Expert selection>>Comfort module Passat B6/CC

General procedure:
Read immo data(PIN & CS code)->Search for 7th byte of CS code when all keys are lost->Make dealer key->Key learning

Good to know:
During “Make dealer key”, we need to program the second key using a dealer key.

2.On-bench programming (Take out CCM)
General procedure:
Take out the Comfort Control Module behind the glovebox
Read the 95320 EEPROM
Make dealer key
Restore back the CCM and program key via OBD

3.Separate Programming (Transponder + Remote)
Try to clone the chip and write the remote in but it doesn’t work. I need sniffer data to clone, so without a working key I can’t clone a ID46 key in this vehicle.

Good to know:
For ID46 key, the remote cannot be programmed separately by OBD; only for ID48 key, we could clone the transponder and program remote via OBD.

Finally he figured out the Reason:

One of two dealer keys is bad.
That’s why the 2nd key will fail no matter the good one or the bad one is programmed firstly.

For remote learning, some customers will recommend OEM software ODIS with an OEM tool (VAS 5054/VAS 6154, VXDIAG VCX SE 6154…).

Thanks to Kurt, Matt, Nick, Popa…

More info, contact us.

Comments

How to Calibrate Mercedes Airmatic control unit by Autel DS708

How to troubleshoot a Mercedes-Benz S-Class that lowers itself when parked? In some cases, the car will drop itself overnight but not always. If the vehicle is parked on an incline or downhill the raising or lowering may stop working. There are many reasons lead to this malfunction. Mercedes-Benz with airmatic suspension tries to level itself when parked and end up with lowering near to the ground. But the vehicle may try to level itself unsuccessfully when one level sensor is broken, or the rod is bent. This may cause your Mercedes-Benz self-level too high or too low. What’s the Symptoms? The following problems may occur on Mercedes-Benz E, C, CLK, GL, S-Class -You hear air compressor engaging when parked. -Air compressor releases air when parked. -Car lowers overnight, not always. -Mercedes lowers drops on rear or front. -Mercedes raises itself when parked Cause When the car is parked the airmatic will try to level the car. It does this by dischargin...

OBDSTAR X300 DP PLUS vs. Autel IM608 vs. Xtool Auto Pro Pad

What do you prefer as automotive key programmers 1 – OBDSTAR X300 DP PLUS 2 - Autel MaxiIM IM608 3 - Xtool Auto pro pad or other tablet? Here’s the true working experience & feedback from a Facebook locksmith group questionnaire. Keep updating. 1) OBDSTAR is very good. works very well really is very good for the price. I have both obdstar and xtool pad2. ObdStar is superior. It works very well on fiat renault bmw and other brands that are not easy to work with another tool. 2) I got the xtool pro pad it works well on cars like newer GMs and Hyundai and Chrysler most fords. Obdstar x300 strictly for Honda Toyota keys and Nissan. And lastly the old t300 for older Fords with the 4c keys. I’m thinking of getting the us version of lonstor. 3) AutoProPad, hands down. Its software is designed specifically for the US market. 4) I’m loving my IM608, the tool not only program the keys, but is an excellent scanner and can program a other units like ELV, dashboard, EZS...

Autel Maxisys Elite Programming and Coding

Since the introduction of OBD II and leading up to modern Hybrids and EVs, computers and software in cars have been expanding at an exponential rate.In-car software is becoming one of the leading needs for service, and updating software may be the only way to fix some of these issues: * Drivability * Fuel Efficiency * Power Loss * Fault Codes * Durability of Mechanical Parts The Programming and Coding function is used to re-flash the vehicle control modules, it allows you to update the computer software on the vehicle to the latest version, as well as to reprogram adaptive data for certain components after making repairs or replacements. NOTE: The Autel OBD2 Scanner programming function can only be applied through connection with the J2534 programming device, which serves as a PassThru interface to establish communication with and transfer data to the vehicle’s ECU. Available programming or coding o...

Autel scanner

Search This Blog