Autel scanner

  We programmed a new remote key to a 2008 Smart Fortwo 451 with Autel MaxiIM IM608 / IM508 because it lost all the keys. Car has the anti-theft indicator on.     Place the ignition switch. If we try to crank it, we got the message that it not programmed. This key is virgin. Procedure: 2008-2015 Smart Fortwo (all keys lost, add key, EVU replacement) with Autel IM608 We go to Diagnostic instead of going to Immobilizer function. Check vehicle information, has vehicle model and vin number here We go to Control unit ->N10/10(SAM control)-> Control unit adaptations->Program key transponder codes Insert key to be programmed into ignition and turn on ignition Press F2 to start learning process Turn off the ignition and then back on. Press key ESC to interrupt rage teach-in process The key has been successfully learned. Press Yes Learning key in progress Press F4 STOP Remove the taught-in vehicle key Insert vehicle keys to be taught in into ignition lock and turn to position ignitio

  Question: 2020 Toyota Highlander all keys lost. Tango fail Zedfull fail Possible to program 2020 2021 Toyota AKL with  Autel IM608 and  XP400 Pro by OBD ? Answer: If it’s add key, autel is able to add it without LSID. Either way, you can try it. If it shows you 3 data lines, then not possible. Autel doesn’t support toyota/lexus 2018+ all key lost yet, still in development.  2018 before AKL requires APB112 emulator. As for lonsdor you’ll need to Lonsdor specific smart key and open AKL license on your device which has to be renewed every year. If all keys lost, it requires Toyota Subscription with techinfo.toyota.com. The newer Toyota’s have an extra security component even adding keys diagnostically will be a problem unless you have the special password.  IM608 can do the ’21 Corolla’s and Camry’s (at least) by OBD as long as you can provide the 12-digit outcode.  The im608 requires a response code of 12 digits, which comes after you submit the 3 lines of data. Autel can

  Test report: successfully add a new remote key to Iveco daily 2017  using  Autel IM508 and XP400 Pro . Couldn’t connect via OBD. Done on bench by dump. Take BCM out – read 95640 with xp400pro and add key via dump. Used key KD remote multifunction, generated as Ducato Magneti Marelli pcf7946. BCM is located the left drivers foot. You need to remove one plastic (without screws, only clips) and then remove 6 or 7 screws, which holds BCM. And of course a lot of plugs. SSOP8 eeprom Read eeprom by xp400 pro using vvdiprog adapter

  The influence of Audi OE strategy changes has led to the suspension of online calculation functions at home and abroad – Announcement from Autel (based on MaxiIM IM608 / IM508 ). What VAG car models are influenced? All Audi IMMO online function is not working, including those from Autel and the method of paying for data calculation from the third party. VW Skoda will not be affected for the time being. List of affected functions. (All Audi Expert Mode functions): A3 2013+ add key (a part) and all keys lost A4 2014 – 2016 add key and all keys lost A5 2014 – 2016 add key and all keys lost A6/A7 2012 – 2017 all keys lost Q2 2018 – 2020 add key (a part)and all keys lost Q3 2012 – 2019 All keys lost Q3 2019 – 2020 add key (a part)and all keys lost Q5 2014 – 2018 add key and all keys lost TT 2016 – 2020 add key and all keys lost Short-term issues and solution: 1. Disable the online immo function and notify the after-sales service. At the same time, follow the OE account stra