2015 BMW 528i Battery Register Replacement by Autel IM608

This is a , and I’ve changed a new battery aftermarket. So I wanna try if this Autel MaxiIM IM608 scan tool can do BMW battery replacement & registration.

Plug Autel IM608 connector into OBD, go access

Diagnostics >> VIN >> Auto detect >> Accept >> OK >> Yes

Turn the ignition off.
Please wait…
Turn ignition on.

Service >> Body >> Voltage supply >> Battery >> Register battery replacement >> Register battery exchange

It’s processing… Wait for 100%.
Press “F1” to register the battery replacement.
Note: the history of the last battery exchange is deleted after programming.

3 kinds of battery capacity, just select from your case.
F1: same capacity
F2: higher/lower capacity.
F3: change from normal lead-acid battery to absorbent Glass Mat(AGM) or EF battery.

Is the newly installed battery an original component? No.
Battery replacement is entered.
Please wait…
The battery exchange was successfully registered.
The following was entered:
Last battery exchange: 139030km
Last but one battery exchange: 0km

Note:
In some engine control unit, it is possible that:
After registration, the last battery exchange and the last but one battery exchange are set to 0 km or can be displayed correctly only after going to the history of the last battery exchange again.

Follow the prompts, continuous press “Continue”.

Note:
Full functionality is only available with a valid state of charge. Functions such as the Automatic Start/Stop function or intelligent generator control can be restricted up to a fully valid charge state or can be unavailable.
The date and time of the vehicle will be set.
If they are not correct, please set date and time manually.
Service function completed.
Done!

This is how to use Autel IM608 Scanner to do register battery replacement for a BMW.

Comments

Autel Maxisys Elite Programming and Coding

Since the introduction of OBD II and leading up to modern Hybrids and EVs, computers and software in cars have been expanding at an exponential rate.In-car software is becoming one of the leading needs for service, and updating software may be the only way to fix some of these issues: * Drivability * Fuel Efficiency * Power Loss * Fault Codes * Durability of Mechanical Parts The Programming and Coding function is used to re-flash the vehicle control modules, it allows you to update the computer software on the vehicle to the latest version, as well as to reprogram adaptive data for certain components after making repairs or replacements. NOTE: The Autel OBD2 Scanner programming function can only be applied through connection with the J2534 programming device, which serves as a PassThru interface to establish communication with and transfer data to the vehicle’s ECU. Available programming or coding o...

How to Calibrate Mercedes Airmatic control unit by Autel DS708

How to troubleshoot a Mercedes-Benz S-Class that lowers itself when parked? In some cases, the car will drop itself overnight but not always. If the vehicle is parked on an incline or downhill the raising or lowering may stop working. There are many reasons lead to this malfunction. Mercedes-Benz with airmatic suspension tries to level itself when parked and end up with lowering near to the ground. But the vehicle may try to level itself unsuccessfully when one level sensor is broken, or the rod is bent. This may cause your Mercedes-Benz self-level too high or too low. What’s the Symptoms? The following problems may occur on Mercedes-Benz E, C, CLK, GL, S-Class -You hear air compressor engaging when parked. -Air compressor releases air when parked. -Car lowers overnight, not always. -Mercedes lowers drops on rear or front. -Mercedes raises itself when parked Cause When the car is parked the airmatic will try to level the car. It does this by dischargin...

How to Activate Autel AP200 OBD2 Scanner with Full Brands

Activation of all brands for Autel AP200 Bluetooth OBD2 scanner is possible, but without special functions (adaptation, coding), only diagnostics for all modules and reset of service intervals. But it is a good alternative for personal use for DIYers. When activated for all brands, the program also performs only diagnostics for all makes. Such an adapter is suitable for personal use and auto-fitting. For car services, it will be a tool for quickly reading errors from all makes. Activation of all Autel AP200 brands in Xdiag ap200 indefinitely You can activate in 2 ways: 1) Through the Autel Start program 2) Through the Xdiag AP200 program, which has shown itself to be on the good side in working with Launch adapters. Here are some images showing Autel ap 200 activations for all brands: Upon activation of Autel ap200 for all brands, you can search Google (i.e famous 4pda.to website). It has instructions to install cracked app and install database for all...

Autel scanner

Search This Blog