Autel scanner

This is a successful demonstration on how to add two new keys for Hyundai Santa FE 2010 by  Autel IM608 when all keys lost. Let’s start it from the key decoding. Tools: LISHI Decoder Autel MaxiIM IM608 Xhorse Dolphin XP-005 key cutting machine MINI Key Tool XSKF01EN smart key Step 1. Make key blades Get door key bitting by LISHI Decoder. Use Xhorse Dolphin XP-005 key cutting machine to make two blades. The keys can only open the car’s door. Step 2. Generate transponder So now we’re going to generate remote by VVDI MINI Key Tool. Press Vehicle Remote>>Hyundai>>Santa Fe>>Elantra KeylessGo ID46 433 Insert the Xhorse XSKF01EN smart key into the coil and press “Generate”. Step 3. Read PIN code Now into the car. Open the Autel IM608. Press IMMO>>Hyundai>>Manual selection>>Europe>>SANTAFE (CM)>>2010-2013>>Smart Key Confirm the vehicle information and enter the main menu. If anything puzzles, here select “Vehi...

Autel IM508 / IM608 Issue: Want to add a key for remote start, and able to program the first key but can’t program the second key on a VW CC 2015. I am assuming the key is locked from the dealer and previously worked with the car. If I put this back in the car since I have a key matched, should I be able to program the two keys properly via OBDII? What he has done to troubleshoot the issue: 1.OBD programming (Expert mode) Path: IMMO>>Volkswagen>>Expert selection>>Comfort module Passat B6/CC General procedure: Read immo data(PIN & CS code)->Search for 7th byte of CS code when all keys are lost->Make dealer key->Key learning Good to know: During “Make dealer key”, we need to program the second key using a dealer key. 2.On-bench programming (Take out CCM) General procedure: Take out the Comfort Control Module behind the glovebox Read the 95320 EEPROM Make dealer key Restore back the CCM and program key via OBD 3.Separate Programming (...

Here’s the guide on adding blade chip key ID8A 2017 2018 2019 2020 2021 Toyota Fortuner by Autel MaxiIM IM508 . Note: add key only. 8A blade key all keys lost requires 8A adapter.  Smart key all keys lost requires 12-digit PIN. Let’s get started. Go to IMMO function- Toyota- Automatic selection This function requires network connection Select Immobilizer- Immobilizer H 8A/8E- Learn Key Make sure you have a master ket. you must have a master key before clear or add another key. Insert learned master key and turn on ignition switch Remove key, insert key to be learned, and keep the ignition off Leave the key in the ignition for 60s Wait the lamp lights go out, learning succeeded Test both keys. If you want to know more about Key Programmer , please visit our website: https://www.obd2tool.com

This is a 2008 Volvo XC70, the client lost all of the keys for the vehicle and we have to program a new semi-smart key to this vehicle with  Autel MaxiIM IM608 and XP400 Pro . In order to do so, we need to remove the CEM module or central electrical module which is located behind the glow component. it’s behind the glove compartment right over there where you see the m plugs it goes right against the wall firewall and you need to remove the glow compartment. Now go to immobilizer section with im608, select Volvo- Manual Selection- XC70 – 2008 to 2010- Semi smart key- confirm vehicle information i’m gonna get a control unit- Read CEM security data We basically have to first read the cem module data okay and then you’re gonna be gonna have to use xp 400 it’s not a very simple programming it might be a little bit confusing for some other people but it’s not hard all you have to do is follow the diagrams follow the instructions and you should be good to go. so...