Autel IM508/IM608 Do Repair BMW CAS3+ ISTAP

BMW X1 2011 CAS3++ istap now cannot turn on with the working key. I downgraded CAS3, did put battery support on (GYS Flash) but Wifi cut out during update. And it failed now no ignition.

Here are the working solutions for those who failed BMW cas3++ via OBD with autel im508/IM608.

2 Solutions:

1. Try Repair online first

2. if not success then try ECUs repair by dump

Solution 1: online repair

There is a repair option with vvdi2 via obd, worth a try first.

If not then autel has a repair option also.

With the im608/im508, you have the repair files, remove CAS, backup what’s left, upload to autel (via 608), receive files back (it’s instant), reinstall repair files.

Check the step-by-step guide in im608 below.

(*If all keys lost situation. It may have also lost ISN so repair will not let car start but ignition will come back. Then you need to read ECU isn and do CAS renew on autel to fix.)

Solution 2: Repair by dump

Need to remove CAS from car and read it with a programmer. NO need to replace CAS.

If you have hextag read the eeprom, put it into hexprog and it can change file to a running file write back to the eeprom, all up and running. Check: Repair BMW CAS3+ Data Corruption with Hextag

If don’t have a hextag, read with other programmer. Read with prog uploaded files to autel for CAS repair , repaired files written back with extra key added works fine.

Autel gives good fix on bench as well.

How to Repair BMW CAS3 and Add a Key with autel maxiim im608?

Model example: BMW X1 CAS3++ istap 2011 with Mask 0L15Y

Step 1: Read EEPROM & FLASH

Uninstall CAS box and welding cable apa109

Left key customer key that cannot start now

Right is new key

Connect xp400 pro and apa109 cable via USB port. The im608 has built in colored schematics with great quality pictures. Soldering is the hardest part.

(How to check wiring diagram: Go to Programmer- Chip -Chip Read & Write – Immobilizer- BMW – CAS3+ – 0L15Y -RW -Schematic diagram)

Select Immo- BMW- Manual Selection- X1- 2008/09-2015/06 E84 – Control unit- CAS3/CAS3+ Immobilizer -ECU operation

Follow the instructions in the help information for strict operation

Show ECUs operation guide and schematic diagram

Select 0L15Y- Read EEPROM

Save eerpom file, i.e BMW CAS3+_0L15Y_OM23S_EEPROM-07052021.bin

Read Flash

Read Flash success, save flash data i.e BMW CAS3+_0L15Y_OM23S_FLASH_07052021.bin

Step 2: ECU Repair

Select Special function- ECU repair- 0L15Y/0M23S

Load the EEPROM file of the current vehicle (select CAS3+_0L15Y_OM23S_EEPROM-07052021.bin read in step 1)

The file is being modified. Save new file.

EEPROM file is saved successfully, i.e CAS3PlusEepromFileEdit-07052021.bin

Load FLASH file (select CAS3+_0L15Y_OM23S_FLASH-07052021.bin read in step 1)

Save new flash file. i.e CAS3PlusFlashFileEdit-07052021.bin

Step 3: How to Add a New Remote Key

Next show how to add new remote

Back to Key operation – Key Learning- Make key with file- 0L15Y/0M23S

Load the EEPROM data, select the new FileEdit eeprom read in step 2

Verify VIN, mileage and frequency information

Choose key position 3 and press write key

Press Add key

Put a working key into xp400 programmer

Reading key information

Read key info successfully, proceed with the next step

Select semi smart key

Put new key into the programmer

Writing key

Save new eeprom file

Flash the new car eeprom file into car, then use the new dealer key to start the engine.

If CAS belong to is istap version, don’t write new file back to CAS.

Go back to ECU Operation- 0L15Y -Write eeprom

Load Modify eeprom bin file

Writing eeprom file successfully

Write flash

Load FileEdit flash file, wait 7-8mints to write flash

Write flash successfully

Now this CAS can start engine with normal operation.

Keep in mind, it’s always a risk doing istap through obd bench is much easier and safer it was a pain to recover the files.

How to Calibrate Mercedes Airmatic control unit by Autel DS708

How to troubleshoot a Mercedes-Benz S-Class that lowers itself when parked? In some cases, the car will drop itself overnight but not always. If the vehicle is parked on an incline or downhill the raising or lowering may stop working. There are many reasons lead to this malfunction. Mercedes-Benz with airmatic suspension tries to level itself when parked and end up with lowering near to the ground. But the vehicle may try to level itself unsuccessfully when one level sensor is broken, or the rod is bent. This may cause your Mercedes-Benz self-level too high or too low. What’s the Symptoms? The following problems may occur on Mercedes-Benz E, C, CLK, GL, S-Class -You hear air compressor engaging when parked. -Air compressor releases air when parked. -Car lowers overnight, not always. -Mercedes lowers drops on rear or front. -Mercedes raises itself when parked Cause When the car is parked the airmatic will try to level the car. It does this by dischargin...

OBDSTAR X300 DP PLUS vs. Autel IM608 vs. Xtool Auto Pro Pad

What do you prefer as automotive key programmers 1 – OBDSTAR X300 DP PLUS 2 - Autel MaxiIM IM608 3 - Xtool Auto pro pad or other tablet? Here’s the true working experience & feedback from a Facebook locksmith group questionnaire. Keep updating. 1) OBDSTAR is very good. works very well really is very good for the price. I have both obdstar and xtool pad2. ObdStar is superior. It works very well on fiat renault bmw and other brands that are not easy to work with another tool. 2) I got the xtool pro pad it works well on cars like newer GMs and Hyundai and Chrysler most fords. Obdstar x300 strictly for Honda Toyota keys and Nissan. And lastly the old t300 for older Fords with the 4c keys. I’m thinking of getting the us version of lonstor. 3) AutoProPad, hands down. Its software is designed specifically for the US market. 4) I’m loving my IM608, the tool not only program the keys, but is an excellent scanner and can program a other units like ELV, dashboard, EZS...

Autel Maxisys Elite Programming and Coding

Since the introduction of OBD II and leading up to modern Hybrids and EVs, computers and software in cars have been expanding at an exponential rate.In-car software is becoming one of the leading needs for service, and updating software may be the only way to fix some of these issues: * Drivability * Fuel Efficiency * Power Loss * Fault Codes * Durability of Mechanical Parts The Programming and Coding function is used to re-flash the vehicle control modules, it allows you to update the computer software on the vehicle to the latest version, as well as to reprogram adaptive data for certain components after making repairs or replacements. NOTE: The Autel OBD2 Scanner programming function can only be applied through connection with the J2534 programming device, which serves as a PassThru interface to establish communication with and transfer data to the vehicle’s ECU. Available programming or coding o...

Autel scanner

Search This Blog