Skip to main content

Autel IM608 = MaxiSys MS908 (Diagnosis) + IMMO Functions

Autel MaxiIM IM608 has the same diagnostic software as Autel maxisys MS908P, but it covers immo functions, special functions and programming/reflashing abilities which MS908p cannot work. Pls read the chart for details
Chart: MaxiIM IM608 vs. MaxiSys MS908 pro
MaxiIM-IM608-vs-MaxiSys-MS908-pro
Autel IM608 key programming:
SMART MOD: Explanatory and Router Key Programming
EXPERT MOD: Advanced Key Programming
*   PIN / CS Reading (Full Lost)
*   Key Generation
*   Key Programming
*   Command Introduction
*   Backup / Repair IMMO Data
*   IMMO ECU Brain Reset / Adaptation
*   IMMO ECU Brain Reset / Coding
*   BENZ 3rd Generation IMMO Key Splicing, Full Lost, Key Programming
*   BMW FEM / BDC Key Programming and ECU Adaptation
*   BMW CAS4 / 3/2 Key Programming
*   VW / AUDI MQB Key Programming, 48 Transponder (96-bit) Key Splicing, Full Lost, A6 Full Lost and More …
IM608 Immo Vehicle Coverage:
Chrysler, Dodge, Ford, GM, Hummer, Jeep, Citroen, Fiat, Jaguar, Land Rover, Maserati, Opel, Peugeot, Renault, Saab, Volvo, Volkswagen, Audi, Bentley, Seat, Skoda, BMW, Mini, Honda, Hyundai, Kia, Lexus, Mazda, Mitsubishi, Nissan, Subaru, Suzuki, Toyota
Pls check Autel MaxiIM IM608 IMMO vehicle list on official website:
https://pro.auteltech.com/measurecarApp-1-1.html?m=94&proTypeCode=IM608(IMMO)&operatorType=2
Autel IM608 chip programming: ( done withXP400 SWITCH)
*   PC Supported
*   MCU / EEPROM Chip Read / Write
*   ECU Reading / Writing
*   MC9S12 Encrypted Chip Read / Write
*   Key Reading / Writing
*   Mercedes Infrared Key Reading / Writing
*   Finding the Control Frequency
*   IC Card Reading / Writing
To sum up,
Autel IM608 key programming function is MUCH better than Autel Maxisys series.
IM608 comes with a XP400 programmer to read/write MCU, EEPROM Chip, IC card, key frequency etc. But Maxisys does not.
Maxisys MS908P could program the ECU of Benz and BMW, and have ECU coding function.
IM608 only could ECU code (ECU coding), could not program ECU of cars.
Both tools have trust and sustainability. Thus, if you are focus on key programming, go for IM608 instead.
If you need a tool for diagnosis only, MS908 is a decent machine at a better price.
Labels:

Comments

Post a Comment

Popular posts from this blog

How to Calibrate Mercedes Airmatic control unit by Autel DS708

How to troubleshoot a Mercedes-Benz S-Class that lowers itself when parked? In some cases, the car will drop itself overnight but not always. If the vehicle is parked on an incline or downhill the raising or lowering may stop working. There are many reasons lead to this malfunction. Mercedes-Benz with airmatic suspension tries to level itself when parked and end up with lowering near to the ground. But the vehicle may try to level itself unsuccessfully when one level sensor is broken, or the rod is bent. This may cause your Mercedes-Benz self-level too high or too low. What’s the Symptoms? The following problems may occur on Mercedes-Benz E, C, CLK, GL, S-Class -You hear air compressor engaging when parked. -Air compressor releases air when parked. -Car lowers overnight, not always. -Mercedes lowers drops on rear or front. -Mercedes raises itself when parked Cause When the car is parked the airmatic will try to level the car. It does this by dischargin...
2 comments
Read more

OBDSTAR X300 DP PLUS vs. Autel IM608 vs. Xtool Auto Pro Pad

What do you prefer as automotive key programmers 1 – OBDSTAR X300 DP PLUS 2 - Autel MaxiIM IM608 3 - Xtool Auto pro pad or other tablet? Here’s the true working experience & feedback from a Facebook locksmith group questionnaire. Keep updating. 1) OBDSTAR is very good. works very well really is very good for the price. I have both obdstar and xtool pad2. ObdStar is superior. It works very well on fiat renault bmw and other brands that are not easy to work with another tool. 2) I got the xtool pro pad it works well on cars like newer GMs and Hyundai and Chrysler most fords. Obdstar x300 strictly for Honda Toyota keys and Nissan. And lastly the old t300 for older Fords with the 4c keys. I’m thinking of getting the us version of lonstor. 3) AutoProPad, hands down. Its software is designed specifically for the US market. 4) I’m loving my IM608, the tool not only program the keys, but is an excellent scanner and can program a other units like ELV, dashboard, EZS...
Post a Comment
Read more

Autel Maxisys Elite Programming and Coding

Since the introduction of OBD II and leading up to modern Hybrids and EVs, computers and software in cars have been expanding at an exponential rate.In-car software is becoming one of the leading needs for service, and updating software may be the only way to fix some of these issues: *   Drivability *   Fuel Efficiency *   Power Loss *   Fault Codes *  Durability of Mechanical Parts The Programming and Coding function is used to re-flash the vehicle control modules, it allows you to update the computer software on the vehicle to the latest version, as well as to reprogram adaptive data for certain components after making repairs or replacements. NOTE: The  Autel OBD2 Scanner programming function can only be applied through connection with the J2534 programming device, which serves as a PassThru interface to establish communication with and transfer data to the vehicle’s ECU. Available programming or coding o...
Post a Comment
Read more