Skip to main content

MS908P VCI – J2534 ECU Programming Device


25-1  25-4
1.Functional Description
1.  Ethernet Port
2.  USB Port
3.  Power LED – illuminates solid green when powered on
4.  Error LED – illuminates solid red when serious hardware failure occurs
5.  Bluetooth LED – illuminates solid green when connected with the MaxiSys display tablet through Bluetooth communication
6.  Ethernet LED – illuminates solid green when connected with the Autel Scan Tool MaxiSys display tablet or an existing LAN via the Ethernet serial cable
7.  USB Status Light — illuminates solid green when the device is properly connected and communicating with the MaxiSys display tablet or the PC via the USB cable
8.  Vehicle LED – flashes green when communicating with the vehicle’s network
IMPORTANT: Do not disconnect the reprogramming device while this status light is on! If the flash reprogramming procedure is interrupted while the vehicle’s ECU is blank or only partially programmed, the module may be unrecoverable.
9.  Bluetooth Antenna
10. DC Power Supply Input Port
11. Vehicle Data Connector (DB26-Pin MVCI)
12. External Programming Voltage Output Port
13. A/D Input Port
J2534 Reprogramming Capability
The J2534 ECU Programming Device is a SAE J2534-1 & -2 compliant PassThru reprogramming interface device. Using the updated OEM software, it is capable of replacing the existing software/firmware in the Electronic Control Units (ECU), programming new ECUs and fixing software-controlled drivability issues and emission issues.
Communication
The J2534 ECU programming device supports Bluetooth, Ethernet and USB communication. It can transmit vehicle data to the MaxiSys display tablet with or without a physical connection. The working range of the transmitter through Bluetooth communication is 755 feet (about 230 m). A signal lost due to moving out of range automatically restores itself when the display tablet unit is brought closer to the VCI unit.
Power Sources
The J2534 programming device can receive power from both of the following
Sources:
Vehicle Power
AC/DC Power Supply
Vehicle Power
The J2534 programming device operates on 12-volt vehicle power, which it receives through the vehicle data connection port. The MS908P powers on whenever it is connected to an OBD II/EOBD compliant data link connector (DLC). For non OBD II/EOBD compliant vehicles, the device can be powered from a cigarette lighter or other suitable power port on the test vehicle using the auxiliary power cable.
AC/DC Power Supply
The J2534 programming device can be powered from a wall socket using the AC/DC power adapter.
Technical Specifications
25-3
Labels:

Comments

Post a Comment

Popular posts from this blog

How to Calibrate Mercedes Airmatic control unit by Autel DS708

How to troubleshoot a Mercedes-Benz S-Class that lowers itself when parked? In some cases, the car will drop itself overnight but not always. If the vehicle is parked on an incline or downhill the raising or lowering may stop working. There are many reasons lead to this malfunction. Mercedes-Benz with airmatic suspension tries to level itself when parked and end up with lowering near to the ground. But the vehicle may try to level itself unsuccessfully when one level sensor is broken, or the rod is bent. This may cause your Mercedes-Benz self-level too high or too low. What’s the Symptoms? The following problems may occur on Mercedes-Benz E, C, CLK, GL, S-Class -You hear air compressor engaging when parked. -Air compressor releases air when parked. -Car lowers overnight, not always. -Mercedes lowers drops on rear or front. -Mercedes raises itself when parked Cause When the car is parked the airmatic will try to level the car. It does this by dischargin...
2 comments
Read more

OBDSTAR X300 DP PLUS vs. Autel IM608 vs. Xtool Auto Pro Pad

What do you prefer as automotive key programmers 1 – OBDSTAR X300 DP PLUS 2 - Autel MaxiIM IM608 3 - Xtool Auto pro pad or other tablet? Here’s the true working experience & feedback from a Facebook locksmith group questionnaire. Keep updating. 1) OBDSTAR is very good. works very well really is very good for the price. I have both obdstar and xtool pad2. ObdStar is superior. It works very well on fiat renault bmw and other brands that are not easy to work with another tool. 2) I got the xtool pro pad it works well on cars like newer GMs and Hyundai and Chrysler most fords. Obdstar x300 strictly for Honda Toyota keys and Nissan. And lastly the old t300 for older Fords with the 4c keys. I’m thinking of getting the us version of lonstor. 3) AutoProPad, hands down. Its software is designed specifically for the US market. 4) I’m loving my IM608, the tool not only program the keys, but is an excellent scanner and can program a other units like ELV, dashboard, EZS...
Post a Comment
Read more

Autel MaxiSys Pro Vehicle Coverage

Autel Maxisys Pro Vehicle Coverage: AUDI, BENZ, BMW, DACIA, EU FORD, LANDROVER, MINI, OPEL, PEUGEOT, RENAULT, SEAT, SKODA, VW, VOLVO, SMART, JAGUAR, BENZ SPRINTER, SAAB, FIAT, ABARTH, LACIA, ALFA ROMEO, VAUXHALL, MAYBACH, BENTLEY, BUGATTI, PORSCHE,GM, CHRYSLER, FORD,SUZUKI, KIA, DAWEOO, ISUZU, TOYOTA, SUBARU, SCION, NISSAN, MITSUBISHI, LEXUS, INFINITI, HYUNDAI, HONDA, ACCURA, MAZDA. Autel MaxiSys Pro MS908P Hardware: 1.Extraordinarily powerful Cortex-A9 quad-core processor 2.9.7” 1,024x768 LED-backlit glossy Multi Touch capacitive display with IPS technology 3.Internal reliable and fast 32GB Solid State Drive for better performance 4.Built-in 5-megapixel rear camera with autofocus and flashlight 5.Dual-band (2.4 GHz & 5.0 GHz) 802.11n Wi-Fi to access your favorite web resources 6.Unique shop tough ergonomic design features strong rubber protection and housing; 7.Built-in rechargeable lithium-ion battery for up to 8 hours of continuous operation 8.USB, audi...
Post a Comment
Read more