How to Read Chrysler Town & Country 2004-2007 Pin Code by Autel IM608 PRO

One customer recently posted feedback that he used Autel MaxiIM IM608PRO to do key programming for Chryslers but the process of pin code reading failed, and it prompted “Not supported”. Besides, he mentioned one is Chrysler Town&Country 2005, the other one is 2007. Here, our engineer gave the solution and has already solved his issue.

Possible reason:

These models (-2007) are too old to read their pin code via OBD.

Solution:

Remove the immo module (SKREEM) to read the EEPROM chip.

1.Remove the SKREEM inside the steering column

1)Remove the screws from the bottom shroud of the steering wheel and take it down.

2)Take down the torque screw beside the module.

3)Remove the ring from around a cylinder.

4)Unplug the plug and remove the SKREEM.

2.Figure out the pin1 of the chip

There are several types of the module like 363AF, 295AF,363AG etc.

Remove the shell and take out the EEPROM.

Figure out the chip, it is marked with the chip type like 95040.

There’s no dimple or notch at the end, so watch what’s called slanted side.

The chip has pins around, but one edge has a slight slant of the pins while another doesn’t and the package goes vertically straight down to the board.

Then the pin1 is in the upper left.

If you puzzle anything, check the diagrams before reading pin code.

Then

1)Use the EEPROM clamp (APA103) to connect pin 1 and Autel XP400PRO

2)Use the USB cable to connect Autel XP400PRO and Autel MaxiIM IM608 PRO.

3.Read the pin code and key programming

Read and save the EEPROM file.

Load the dump file to get key information including the pin code.

Make a new key by the dump file.

Save the newly generated key file.

Write the new bin file to the chip.

Done!

Comments

How to Calibrate Mercedes Airmatic control unit by Autel DS708

How to troubleshoot a Mercedes-Benz S-Class that lowers itself when parked? In some cases, the car will drop itself overnight but not always. If the vehicle is parked on an incline or downhill the raising or lowering may stop working. There are many reasons lead to this malfunction. Mercedes-Benz with airmatic suspension tries to level itself when parked and end up with lowering near to the ground. But the vehicle may try to level itself unsuccessfully when one level sensor is broken, or the rod is bent. This may cause your Mercedes-Benz self-level too high or too low. What’s the Symptoms? The following problems may occur on Mercedes-Benz E, C, CLK, GL, S-Class -You hear air compressor engaging when parked. -Air compressor releases air when parked. -Car lowers overnight, not always. -Mercedes lowers drops on rear or front. -Mercedes raises itself when parked Cause When the car is parked the airmatic will try to level the car. It does this by dischargin...

OBDSTAR X300 DP PLUS vs. Autel IM608 vs. Xtool Auto Pro Pad

What do you prefer as automotive key programmers 1 – OBDSTAR X300 DP PLUS 2 - Autel MaxiIM IM608 3 - Xtool Auto pro pad or other tablet? Here’s the true working experience & feedback from a Facebook locksmith group questionnaire. Keep updating. 1) OBDSTAR is very good. works very well really is very good for the price. I have both obdstar and xtool pad2. ObdStar is superior. It works very well on fiat renault bmw and other brands that are not easy to work with another tool. 2) I got the xtool pro pad it works well on cars like newer GMs and Hyundai and Chrysler most fords. Obdstar x300 strictly for Honda Toyota keys and Nissan. And lastly the old t300 for older Fords with the 4c keys. I’m thinking of getting the us version of lonstor. 3) AutoProPad, hands down. Its software is designed specifically for the US market. 4) I’m loving my IM608, the tool not only program the keys, but is an excellent scanner and can program a other units like ELV, dashboard, EZS...

Autel Maxisys Elite Programming and Coding

Since the introduction of OBD II and leading up to modern Hybrids and EVs, computers and software in cars have been expanding at an exponential rate.In-car software is becoming one of the leading needs for service, and updating software may be the only way to fix some of these issues: * Drivability * Fuel Efficiency * Power Loss * Fault Codes * Durability of Mechanical Parts The Programming and Coding function is used to re-flash the vehicle control modules, it allows you to update the computer software on the vehicle to the latest version, as well as to reprogram adaptive data for certain components after making repairs or replacements. NOTE: The Autel OBD2 Scanner programming function can only be applied through connection with the J2534 programming device, which serves as a PassThru interface to establish communication with and transfer data to the vehicle’s ECU. Available programming or coding o...

Autel scanner

Search This Blog