Autel IM608 Pro Program Mercedes W209(2006-) All Keys Lost

What happen if you lost all Mercedes keys? Luckily Autel has a solution for that, having the Autel G-BOX2 Tool working together with Autel MaxiIM IM608 Pro, the process can be cut down 80% to save time.

2 ways of using G-BOX2 to program Mercedes AKL

♦ Connect with OBD2 port;
♦ Dissemble EIS component, work with that separately from the vehicle.

Parts also needed:

XP400 Pro, cable to connect XP400 Pro with EIS component, JVCI, JVCI cable.

Note: make sure the Internet is strong

Press on Autel IM608 Pro,

Smart selection >> All keys lost(Fast) >> On bench(G-Box Fast) >> W209/2006-

Connect wires to EIS component according to the diagram. Press “OK”.

Insert a blank key into the IR keyhole on XP400 Pro programmer, press “OK”.

Is there a key password? No

We don’t have the password, so press “OK” to enter password calculation.

Begin >> OK

Note: do not disconnect the relevant connection and follow the instructions.

Connect the device, OBD cable and OBD connector on the wiring harness in sequence.

Note: ensure that the EIS is disconnected form the steering column lock.

Connect the IR key simulator(APB102/APB125) to the programmer.

Insert the IR key simulator(APB102/APB125) into EIS.

If it is already inserted, remove and insert it again.

Take our the cable from the EIS and quickly put it back in.

The key password calculation process will take up to 5 minutes…

Succeed in computing password.

Password calculation completed!

Press “OK”

Insert the blank key into IR keyhole on the XP400 Pro programmer, press “OK”.

Writing key file…

All keys lost completed. Press “OK”.

Check if the new key can be used normally according to instructions.

Assemble the EIS back into the vehicle and test the key:

If the red indicator lamp on the key lights up and goes off, the key learning is successful.

If the red indicator lamp stays lit, try inserting and removing the key for several times. If still not working, the key addition failed.

If you don’t have a G-BOX2, you need to put a blank key in and out of the ignition hundreds of times, but with the G-BOX2 you don’t need to do any of that.

This is programming Mercedes Benz W209(2006-) all keys lost. With Autel IM608 Pro & G-BOX2 makes things much simpler.

Comments

How to Calibrate Mercedes Airmatic control unit by Autel DS708

How to troubleshoot a Mercedes-Benz S-Class that lowers itself when parked? In some cases, the car will drop itself overnight but not always. If the vehicle is parked on an incline or downhill the raising or lowering may stop working. There are many reasons lead to this malfunction. Mercedes-Benz with airmatic suspension tries to level itself when parked and end up with lowering near to the ground. But the vehicle may try to level itself unsuccessfully when one level sensor is broken, or the rod is bent. This may cause your Mercedes-Benz self-level too high or too low. What’s the Symptoms? The following problems may occur on Mercedes-Benz E, C, CLK, GL, S-Class -You hear air compressor engaging when parked. -Air compressor releases air when parked. -Car lowers overnight, not always. -Mercedes lowers drops on rear or front. -Mercedes raises itself when parked Cause When the car is parked the airmatic will try to level the car. It does this by dischargin...

OBDSTAR X300 DP PLUS vs. Autel IM608 vs. Xtool Auto Pro Pad

What do you prefer as automotive key programmers 1 – OBDSTAR X300 DP PLUS 2 - Autel MaxiIM IM608 3 - Xtool Auto pro pad or other tablet? Here’s the true working experience & feedback from a Facebook locksmith group questionnaire. Keep updating. 1) OBDSTAR is very good. works very well really is very good for the price. I have both obdstar and xtool pad2. ObdStar is superior. It works very well on fiat renault bmw and other brands that are not easy to work with another tool. 2) I got the xtool pro pad it works well on cars like newer GMs and Hyundai and Chrysler most fords. Obdstar x300 strictly for Honda Toyota keys and Nissan. And lastly the old t300 for older Fords with the 4c keys. I’m thinking of getting the us version of lonstor. 3) AutoProPad, hands down. Its software is designed specifically for the US market. 4) I’m loving my IM608, the tool not only program the keys, but is an excellent scanner and can program a other units like ELV, dashboard, EZS...

Autel Maxisys Elite Programming and Coding

Since the introduction of OBD II and leading up to modern Hybrids and EVs, computers and software in cars have been expanding at an exponential rate.In-car software is becoming one of the leading needs for service, and updating software may be the only way to fix some of these issues: * Drivability * Fuel Efficiency * Power Loss * Fault Codes * Durability of Mechanical Parts The Programming and Coding function is used to re-flash the vehicle control modules, it allows you to update the computer software on the vehicle to the latest version, as well as to reprogram adaptive data for certain components after making repairs or replacements. NOTE: The Autel OBD2 Scanner programming function can only be applied through connection with the J2534 programming device, which serves as a PassThru interface to establish communication with and transfer data to the vehicle’s ECU. Available programming or coding o...

Autel scanner

Search This Blog